Motobike Más

80/100-21 Mousse Insert: Motocross Front Wheel Fitment Guide

Motobike Mas 80/100-21 professional enduro mousse insert for full-size motocross and supercross front wheels

An 80/100-21 front tire takes a foam insert cut to that one tire — 80 mm section width, 100% profile, 21 inch rim — and Motobike Más makes it in closed-cell nitrile rubber. Because the insert carries the load that compressed air would otherwise carry, a bad landing or a square-edge rock cannot deflate the front wheel, and the up-to-40% reduction in rotating mass against a tube plus a heavy-duty rim lock is what changes the way the front end behaves over a race. The tire around the insert is still inflated with air in the normal way: the mousse provides the structure, and the air still sets the profile, the grip and the rolling resistance.

Motobike Más builds the 80/100-21 Professional Enduro Mousse (SKU MMO-007) in its own Tianjin factory. It is the traditional full-size motocross and supercross front size — a shorter, stiffer carcass than the 90/90-21 on the same rim — and it remains the factory default on the widest population of full-size dirt bikes in the world. It is published in three density grades, Soft, Medium and Standard, so a distributor can cover supercross, general motocross and desert racing from one SKU. This guide covers the specifications, how it compares with the 90/90-21, density selection, the machines it fits, service life and how distributors order it.

Dernière mise à jour : 19 novembre 2026. Sources des données : the published Motobike Más specifications for MMO-007, the factory’s published fitment, density, pressure and lifespan tables, and the factory’s size and certification documentation. Figures shown as “≈” are calculated from the published tyre size designations rather than measured by the factory.

What is an 80/100-21 mousse insert?

An 80/100-21 is built the opposite way round from the 90/90-21 that shares its 21 inch rim. Here the section width is 80 mm and the aspect ratio is 100%, so the sidewall is exactly as tall as the tire is wide — 80 mm. The result is a shorter, stiffer carcass than the 90/90-21, and almost exactly the same overall diameter: roughly 693 mm against roughly 695 mm.

That combination is the reason the 80/100-21 has been the standard motocross front tire for decades. A stiffer sidewall carries the load through the tire rather than absorbing it, which keeps the front wheel lighter and sharper, and a shorter profile gives the rider a quicker change of direction through a corner entry. Where the 90/90-21 buys compliance and grip, the 80/100-21 buys response.

The mousse insert sits inside that carcass and does the job the inner tube would otherwise do. Because there is no air chamber left to lose, a rock, a root or a landing cannot deflate the front wheel. On a motocross track the front wheel is the end of the bike that is being asked to do the most violent work — it takes the braking, the corner entry, the landing and the acceleration out of the exit — and losing it suddenly is the failure that ends a race before it starts.

Professional off-road motorcycle racing through desert terrain at sunset on Motobike Mas high performance tires

A mousse cannot change the size of the tire, and the 80/100-21 is a size with no second option. The insert is cut for an 80 mm section width on a 100% aspect ratio on a 21 inch rim, and it will not seat correctly in a 90/90-21 or a 90/100-21 tire even though all three run on the same rim diameter. The size-by-size compatibility rules are in the Guide des tailles des inserts en mousse, and the fitting method is in the Guide d'installation de l'insert en mousse.

80/100-21 technical specifications

Read off the sidewall, 80/100-21 means an 80 mm section width, a 100% aspect ratio and a 21 inch rim diameter. The section width is how much rubber the tire puts on the ground; the aspect ratio is how tall the sidewall is as a percentage of that width. At 100% the two numbers are the same, giving an 80 mm sidewall and an overall diameter of roughly 693 mm on a 21 inch rim.

That diameter is almost identical to the 90/90-21 front, which is why the two sizes roll at the same speed and can be swapped between machines without touching gearing. It is also why they are so easily confused in a parts order: they look the same, roll the same and share a rim diameter, but the section width and the profile are different, and the mousse insert is cut for one and not the other.

Published data for the 80/100-21 against values confirmed on request
Donnée Valeur Statut
Désignation de la taille 80/100-21 — 80 mm section, 100% aspect ratio, 21 in rim Publié
Référence MMO-007 Publié
Classes de densité Souple / Moyen / Standard Publié
Poids unitaire Approximately 0.9–1.1 kg Publié
Pression effective équivalente 8 à 12 psi selon la qualité Publié
Durée de vie 200 à 500 miles de course Publié
Réduction de la masse en rotation Jusqu'à 40% contre une chambre à air, plus un verrou de jante ultra-résistant Publié
Pays d'origine Tianjin, Chine Publié
Tolérance dimensionnelle par lot Par lot de production Confirmé sur demande
Tolérance relative à la densité interne du lot Par lot de production Confirmé sur demande
Dénominations actuelles des catégories et tranches de poids des coureurs Par référence Confirmé sur demande
Overall diameter comparison for the 80/100-21 and the sizes it competes with
Taille Largeur de la section Format d'image Hauteur du flanc Diamètre de la jante Diamètre total
80/100-21 — this size 80 mm 100% ≈ 80 mm 21 in ≈ 693 mm
90/90-21 90 mm 90% ≈ 81 mm 21 in ≈ 695 mm
90/100-21 — rally front 90 mm 100% ≈ 90 mm 21 in ≈ 713 mm
110/90-19 — typical rear 110 mm 90% ≈ 99 mm 19 pouces ≈ 681 mm
120/80-19 — alternative rear 120 mm 80% ≈ 96 mm 19 pouces ≈ 675 mm

Les valeurs “ ≈ ” sont calculées à partir des désignations de dimensions publiées : la hauteur du flanc correspond à la largeur de la section multipliée par le rapport d'aspect, et le diamètre total correspond au diamètre de la jante plus deux fois la hauteur du flanc. Elles sont utiles pour comparer les dimensions entre elles et ne constituent pas des mesures effectuées en usine ; l'usine confirme les dimensions mesurées sur demande. Le tableau complet des diamètres pour chaque dimension publiée se trouve sur la page Guide des tailles des inserts en mousse.

What a 100% aspect ratio does on a motocross front wheel

A 100% aspect ratio means the sidewall is exactly as tall as the tire is wide, and on the 80/100-21 that produces a distinctly different behaviour from the 90/90-21 on the same rim.

It carries load instead of absorbing it. A short, stiff sidewall deflects less under braking and cornering load, so more of the energy goes into the contact patch and less is soaked up by the carcass. On a hard-packed track, where the surface is predictable and the tires are working at their limit, that is exactly what you want: the tire stays planted and the bike stays predictable.

It changes the corner entry. A shorter profile with a narrower footprint puts the tire on the ground sooner and with less compliance in the sidewall, so the bike turns in more sharply when the rider asks it to. Supercross layouts built around tight rhythm sections reward that directly.

It gives up somewhere, and the somewhere is rocks. A stiffer sidewall has less travel to give when a tire meets a square edge, so more of that impact is transmitted to the rim and to the rider’s arms. This is the trade that makes the 80/100-21 a motocross tire and the 90/90-21 an enduro and trail tire, and it is why the choice between them is a choice about terrain rather than about quality.

It changes the contact patch shape. With less sidewall deflection the 80/100-21 develops a shorter and wider patch at a given pressure. In deep loam that is an advantage, because a wide flat footprint floats on top of the soil instead of cutting into it. In sand, where the tire climbs and the front lightens, the same behaviour means less bite, and the 90/90-21 with its taller, more compliant carcass is generally the better tool.

The terrain consequences of all four points are set out in the section on berms, deep loam and hard-pack below, and the size-by-size comparison is in the Guide des tailles des inserts en mousse.

The three density grades and how to choose between them

This size is published in three named density grades — Soft, Medium and Standard — and each grade comes with a published effective pressure equivalent and a published rider-weight band. The grade measures how hard the foam itself is; it is not the pressure you put in the tire. How that figure relates to an equivalent tire pressure, and the grade-naming convention used across the different sizes in the range, is explained in full on the Guide des tailles des inserts en mousse.

On the 80/100-21 the grade is doing a very specific job. The front wheel of a motocross bike spends its life taking the sharpest inputs on the bike — the landing, the rock, the compression — and the grade decides whether the foam absorbs that input or transmits it. A softer grade gives more grip and more compliance before it gives up; a firmer grade holds together longer on hard, fast, rocky terrain.

Published density grades, effective pressure and rider-weight bands for the 80/100-21 front wheel
Classe de densité Pression effective équivalente Consignes relatives au terrain publiées Fourchette de poids des coureurs publiée
Douceur 8 à 10 psi Mud, sand, wet and slippery conditions, supercross Moins de 70 kg
Moyen 9 à 11 psi Terrain varié, motocross polyvalent 70–90 kg
Standard 10 à 12 psi Un désert rocailleux, au sol dur et compact, où l'on roule à grande vitesse Plus de 90 kg

For a motocross and supercross customer base, the Middle and Soft grades are the volume sellers, because they cover the two dominant conditions: a prepared track with a hard surface, and a rough natural track in the wet. The Standard grade covers hard and fast terrain where the bike is at full lean for long sections, and it is also the grade published for the heaviest riders on this size.

One point of discipline for buyers: the rider-weight bands are published per size, and they are not interchangeable. A rider who is comfortable on the middle grade of one size is not automatically on the middle grade of another — the 70/100-19 youth front, for example, starts its softest grade at under 50 kg against under 70 kg here. The factory confirms the current band boundaries for this SKU on request.

80/100-21 or 90/90-21: which front size should a distributor stock?

Two front sizes dominate the full-size off-road market, and confusing the two is the most common sizing error a distributor makes. The 80/100-21 and the 90/90-21 are not two versions of the same part — each size has its own insert, cut to its own tire, and each needs its own front mousse. Between them they cover almost every full-size machine sold, which is why most distributors stock both.

80/100-21 compared with 90/90-21 front mousse
Spécifications 80/100-21 90/90-21
Largeur de la section 80 mm 90 mm
Format d'image 100% 90%
Diamètre total Légèrement plus petit Légèrement plus grand
Steering feel Une réponse plus légère et plus rapide Meilleure adhérence, légèrement plus lourd
Best for Motocross, supercross, pistes très compactes Enduro, terrain meuble, tout-terrain technique
Front-end grip Good — quicker steering at the cost of ultimate grip Excellent — more rubber on the ground
Mousse weight 0.9–1.1 kg 1.0–1.2 kg

The line worth dwelling on in that table is the overall diameter. The 90/90-21 has a 90 mm section width on a 90% aspect ratio; the 80/100-21 has an 80 mm section width on a 100% aspect ratio. Both land on almost the same sidewall height, 81 mm against 80 mm, and therefore almost the same overall diameter, roughly 695 mm against 693 mm.

That similarity is a trap. The two tires look interchangeable from the outside and roll at almost the same speed, but they are different carcass profiles with different section widths, and a mousse insert is cut for one of them and not the other. The 80/100-21 has 10 mm less rubber on the ground and a shorter, stiffer sidewall; the 90/90-21 has 10 mm more rubber and 1 mm more sidewall.

How a dealer or team should split stock between the two sizes

The two sizes reach a dealer through different channels, and that is what makes the stocking split a purchasing problem rather than a technical one.

The 80/100-21 is the shop-shelf size. It is the size a motocross mechanic reaches for when a rider walks in with a bike, it is the size a race team consumes by the set, and it is the size that moves fastest in the week before an event. Its demand is lumpy but large, and the inventory risk is having too little of it at the wrong weekend.

The 90/90-21 is the enduro and adventure size. Its customer base is smaller but steadier: those riders are on the trails every weekend rather than at a track once a month, and they replace inserts steadily across a season instead of in a single burst before a race.

The practical read for most dealers is that the 80/100-21 deserves the depth and the 90/90-21 deserves the presence. Both are the same line and the same tooling, so they cost nothing extra to carry together, and a customer who has switched from a track to the trails is the customer who buys the 90/90-21 next. Neither size can be substituted for the other — the insert is cut for one tire and one rim — which is exactly why holding both is the cheapest way to keep that customer from shopping elsewhere.

For a distributor the decision is commercial rather than technical, and it is worth being deliberate about it.

The 80/100-21 is normally the faster-moving of the two. It is the factory-standard front on full-size motocross and supercross machinery, and those machines have the largest dealer, media and race-team populations of anything in the category. The 90/90-21 sells into enduro, cross-country and adventure platforms, which have a smaller but longer-lived customer base: enduro riders replace inserts over many seasons rather than every race weekend, so repeat business per machine is higher but the machine population is lower.

The practical stock split for most distributors is therefore a heavier 80/100-21 position with a meaningful 90/90-21 position behind it, and both stocked across the density grades their customer base actually runs. Both sizes share the same manufacturing line, the same MOQ mechanism and the same 15–30 day OEM lead time, so there is no operational reason to carry one and not the other — the reason to carry both is simply that a customer who walks in with a bike on an 80/100-21 front cannot be served with a 90/90-21 insert.

Buyers who need only one of the two should check the front tire size on the machine before ordering. The size is printed on the sidewall, and the Guide des tailles des inserts en mousse lists every size the factory currently publishes. For the wider wholesale picture, see the Guide d'achat en gros.

Which machines use an 80/100-21 front tire?

Full-size machines that use an 80/100-21 front tire
Classe Modèles
250cc motocross Honda CRF250R, Yamaha YZ250F, KTM 250 SX-F, Husqvarna FC 250, Kawasaki KX250, Suzuki RM-Z250, GasGas MC 250F
450cc motocross Honda CRF450R, Yamaha YZ450F, KTM 450 SX-F, Husqvarna FC 450, Kawasaki KX450, Suzuki RM-Z450
Enduro / cross-country / dual sport KTM 300 XC-W, KTM 350 EXC-F, KTM 500 EXC-F, Husqvarna TE 300, FE 350, FE 501, Beta RR 300 / RR 350 / RR 430 / RR 480, Sherco SE 300 / SE 500 / SE 700, GasGas EC 250 / EC 300, Honda CRF450X / CRF450RL, Yamaha WR250F / WR450F, Suzuki RMX450Z

The list above is the population of full-size machines on which the 80/100-21 is factory-standard, and it is the largest single fitment list the factory publishes. The group worth pulling out separately is the supercross and track-focused side of the market: supercross machines are built around short, tight, high-speed rhythm sections on a prepared surface, and the 80/100-21’s short, stiff, light front is the configuration those bikes are set up with.

It is also worth noting where the 80/100-21 is not the default. Adventure and rally platforms that keep a 21 inch front — the Honda CRF450X and CRF450RL, Yamaha WR250F and WR450F, Suzuki RMX450Z — use the taller 90/90-21 on most factory configurations and the 90/100-21 for desert work, covered in the 90/100-21 rally mousse guide. A distributor serving the full range should be holding all three 21 inch front sizes, and the mousse selection guide for enduro riding explains how to match a size to the terrain a customer actually rides.

Berms, deep loam and hard-pack: how terrain changes the front tire choice

The 80/100-21 is not universally the better front tire. It is the better front tire for a specific set of conditions, and knowing which conditions those are is worth more to a buyer than any specification number.

How common off-road terrain changes the choice between the two full-size 21 inch front sizes
Terrain or condition What it does to the front tire Better front size Why
Hard-packed prepared track Predictable surface, sustained high-speed compression 80/100-21 Shorter, stiffer profile holds a line and keeps the steering light
Berms Sharp lip on the exit that the front tire has to climb 80/100-21 Quicker turn-in to set the bike up for the next corner
Deep loam Tire sinks and has to be pushed out of the soil 80/100-21 in a loam setup Wide, flat footprint floats on the soil instead of cutting into it
Rock gardens and roots Square-edge impacts at the front wheel 90/90-21 81 mm sidewall absorbs the impact instead of the rim
Sand and dunes Tire climbs, front end lightens, steering goes vague 90/90-21 More rubber on the ground and more compliance hold the front in the sand
Wet roots and mud Tires dig in and slide rather than biting 90/90-21 with the softer grade Wider footprint and compliance find grip in the mud
Desert and fast gravel Heat, high speed and heavy load through the front 90/100-21 Taller, heavier-duty rally front built for that load

Two practical consequences follow for a distributor. First, most customers do not change front tire size when they change terrain — they change the density grade within the size they already run. That is what makes the four-grade range on the 80/100-21 commercially valuable, and it is why grade depth matters more than size depth for most accounts.

Second, the customers who do change size are almost always moving between the 80/100-21 and the 90/90-21, and they are usually moving because their riding moved from prepared track toward natural terrain or the other way round. The two sizes therefore sell each other, and a distributor who holds both converts more of the second question than a distributor who holds one.

What a front tire loses when it goes down

On a motocross bike the front wheel is asked to do three things at once: it takes the braking, it takes the corner entry, and it takes whatever the rear wheel has just thrown at it over a crest. The 80/100-21 front is where all of that lands, and it is where a deflation becomes a crash rather than a lost lap.

Consider a berm exit with the front already loaded. The tire is in full compression, the rider is on the throttle, and the tire takes a square edge out of the corner. With an inner tube in the tire, a pinch or a puncture empties the air and the front goes light in a corner entry that is already committed. With a mousse in the tire, there is no chamber left to empty, the rim still ends up carrying the load, and the rider keeps a steering input that is still worth making.

What an 80/100-21 front tire loses to a deflation during a motocross race
Front-wheel consequence With an inner tube With a mousse insert
Deflation in a berm exit A crash in a corner already committed The rim carries the load and the rider keeps steering
Steering over a race Drifts as the pressure moves with heat Held steady for the life of the tire
Between race rebuilds A pressure check every session Fit once, then inspect at each rebuild

For a race team the line that matters in that table is the second one. A tube’s pressure moves with temperature and with altitude, and a 30-minute moto is long enough for the tire the rider tuned in practice to be a different tire by the finish of the race. The mousse holds the carcass behaviour steady for the whole life of the tire, and a rider who can trust the front does not have to re-learn the bike every time the track changes temperature.

The third line matters to a dealer. A tire that shreds on a rock does not also mean a new insert, because a serviceable mousse transfers straight into a new tire of the same size. Across a season of rebuilds that is the difference between a customer ordering one item and a customer ordering two.

The general comparison across sizes, including the rear-wheel cases and the cost side of the argument, is in Insert en mousse ou chambre à air ?, et les différents systèmes à cellules fermées sont comparés dans La mousse face au système Tubliss.

Supercross and motocross are not the same front setup

The 80/100-21 serves both, and buyers often assume the fitment is interchangeable because the tire size is identical. The tire is identical; the setup around it usually is not.

A supercross is built around short, tight, high-speed rhythm sections on a prepared surface, with almost no elevation change and a very narrow range of speeds. The bike is ridden hard on the throttle from the first corner, the suspension is set stiff, and the front tire spends its life in hard, sustained compression at the base of a bowl. Under those conditions the priority is a front tire that turns in immediately and holds a predictable line, and the stiffer 100% aspect ratio of the 80/100-21 is exactly that.

Motocross on a natural track is a different animal. There is more elevation change, more of the surface is soft or broken, and the front wheel regularly lands from a jump or drops off a crest. Those are the conditions in which the 90/90-21’s taller sidewall earns its place, and they are also the conditions in which a softer density grade tends to be specified.

For a distributor this has a concrete consequence: a supercross customer and a motocross customer can run the same tire size and need different grades. The Medium grade, which is the volume seller on prepared tracks, behaves very differently on a soft natural track, and the published terrain guidance on this page is the starting point for a customer conversation rather than an answer. A racer who says their bike “does not hold the front” on a natural track is usually describing a grade that is too firm for the surface, not a tire that is the wrong size.

The factory’s own position on the whole range is set out in the guide to choosing a motorcycle mousse for enduro riding, and the differences between the closed-cell systems are covered in La mousse face au système Tubliss.

Installing an 80/100-21 front mousse insert

N'utilisez jamais de lubrifiants à base de pétrole sur un insert en mousse. Petroleum products degrade nitrile rubber, and a degraded insert is a liability, not a saving. Use water-based mousse lubricant only, on both the insert and the bead seat of the rim.

La séquence générale — préparation du logement du talon, application du lubrifiant, premier talon, deuxième talon, mise en place définitive et cycle de pression permettant de définir le profil — est décrite dans le Guide d'installation de l'insert en mousse et s'applique tel quel à cette taille.

Check the rim width before the tire goes on. The 80/100-21 leaves more rim wall than the 90/90-21 does, but the tire’s own fitment marking still has to be checked against the rim width before the tire is mounted. A forced insert sits off-centre and makes the steering feel vague in every corner, and on a bike that is leaned over and being flicked from berm to berm that vague feeling is a lap time, not a comfort issue.

Inspect the insert at every rebuild. A motocross wheel comes off between races and often more than once in a race day, and every rebuild levers a bead back over a rim. That is when an insert gets pinched and takes a compression set that cannot be seen from the outside, so the insert should be looked at each time the wheel is stripped rather than trusted from the last time it was fitted.

Quelle est la durée de vie d'une mousse avant de type 80/100-21 ?

On the 80/100-21 front, life is usually quoted in racing miles rather than hours, because a motocross insert is consumed by track time rather than distance covered on the road. Motobike Más publishes 200–500 racing miles as the typical figure for this product.

Published 80/100-21 front insert life by the use case it is run in
Front-wheel use Expected front insert life Tires per insert
Professional motocross on a groomed, hard-packed track 30 à 60 heures 1 to 2
Amateur motocross on varied track conditions 50 à 80 heures 2 to 3
Supercross on a prepared, high-speed layout 25 à 50 heures 1
Desert and rally racing on fast rough terrain 30 à 60 heures 1 to 2

The front generally outlasts the rear on the same machine, and the reason is load rather than geometry: the front wheel absorbs braking energy and cornering loads, while the rear carries drive torque and the engine’s power through the tire for the whole event. A front insert also works against less heat, and heat is what ages closed-cell foam fastest.

For a motocross customer the practical limit is often not the mileage but the number of rebuilds. A club racer running six events a season on one pair of tires gets through a front insert well before the published mileage, because the insert is removed and refitted far more often than it is ridden. The full published lifespan table for every use case, and the replacement criteria that apply across the whole range, are on the Guide des tailles des inserts en mousse, mousse insert lifespan et how long a motorcycle mousse lasts.

How the 80/100-21 is manufactured and tested

Motobike Más fabrique de la mousse dans son usine de Tianjin, située dans le district de Nankai, qui s'étend sur 50 000 m² comprenant des zones de production, des entrepôts et des locaux dédiés à la R&D. L' Visite guidée complète de l'usine présente les chaînes de production, le système de stockage et les systèmes de qualité qui sous-tendent cette gamme.

The 80/100-21 is the highest-volume front size on the line, and that brings a specific manufacturing requirement: the 80 mm section width has to be held tightly across production runs, because the profile of the front tire depends on the profile of the foam inside it, and a team that fits a new batch of inserts should not have to rebuild its setup because a batch ran slightly different. Dimensional inspection is therefore the check that matters most on this size, alongside the density, compression recovery, heat resistance and structural integrity verification every insert passes before packing. The full inspection regime is described in the Présentation du processus de contrôle qualité.

Commander chez Motobike Más : quantité minimale de commande, délai de livraison, frais d'expédition et échantillons

The 80/100-21 is supplied as a made-to-order factory line rather than from finished-goods stock, and for a motocross-facing business the timing is the part of the table that matters.

B2B ordering terms for the 80/100-21 enduro mousse insert
Term Détail
MOQ Contact the factory for current minimums
Lead time Typically 15–30 days for standard OEM production, depending on quantity and customization
Expédition Sea (FOB Tianjin), air freight, and DDP available
Échantillons Pre-production samples available for evaluation
OEM / ODM OEM mousse production with custom branding, packaging and colours, custom density formulations including front-specific formulations, and distributor partnerships

Motocross and supercross demand arrives in blocks rather than steadily, ahead of a race weekend, and a 15–30 day lead time means the order has to be placed before the demand shows up rather than after it. Dealers who order against a published event calendar, and race teams who consume a set per bike per weekend, are the customers this lead time is built around, and pre-production samples are the way to confirm the compound before committing to that cadence.

For stock planning, the useful combination is the 80/100-21 with the 90/90-21. Both are front sizes on the same production line with the same tooling, so they can travel on a single purchase order, and a customer who has moved from a prepared track to natural terrain is exactly the customer who moves between them. The general OEM and ODM route, including private-label packaging and custom density formulations, is set out in Fabrication OEM et ODM et the wholesale buying guide.

Frequently asked questions about the 80/100-21 mousse insert

La référence 80/100-21 correspond-elle à un pneu avant ou arrière ?

80/100-21 is a front wheel tire size and the classic motocross front standard. It has been the dominant front size on full-size motocross and supercross bikes for decades, and it is still the factory default on a wide list of 250cc and 450cc motocross platforms. It is a 21 inch size with an 80 mm section width and a 100% aspect ratio.

Quelle est la différence entre les dimensions 80/100-21 et 90/90-21 ?

The 80/100-21 has an 80 mm section width on a 100% aspect ratio, so it has an 80 mm sidewall. The 90/90-21 has a 90 mm section width on a 90% aspect ratio, so it has an 81 mm sidewall. The two therefore have almost the same overall diameter, roughly 693 mm against 695 mm, but the 80/100-21 is lighter and quicker to turn in while the 90/90-21 puts 10 mm more rubber on the ground and absorbs square-edge impacts better. The 80/100-21 is the motocross and supercross choice; the 90/90-21 is the enduro, trail and loose-terrain choice.

Puis-je utiliser une mousse 80/100-21 dans un pneu 90/90-21 ?

No. Mousse inserts are size-specific and are cut for one tire size and one rim diameter. Although both tires run on a 21 inch rim, the 80/100-21 insert is cut for an 80 mm section width on a 100% aspect ratio and will not seat correctly in a 90/90-21 tire. Using the wrong size results in improper fitment, reduced performance and a safety risk.

Pourquoi les pilotes de motocross préfèrent-ils les pneus 80/100-21 aux pneus 90/90-21 ?

On a prepared motocross track the surface is predictable and the bike is at the limit in sustained compression, so the priority is a front tire that holds a line and turns in immediately. The 80/100-21 has a shorter, stiffer sidewall and a published unit weight of 0.9 to 1.1 kg against 1.0 to 1.2 kg for the 90/90-21, which is felt as faster turn-in and lighter handling in tight rhythm sections and berms.

Which density should I choose for the 80/100-21 front wheel?

Three grades are published for this size: Soft, Medium and Standard, each with its own effective pressure equivalent and rider-weight band. The Soft grade is published for riders under 70 kg on mud, sand, wet and slippery conditions including supercross layouts, at 8 to 10 psi. The Medium grade is published for riders 70 to 90 kg on mixed terrain and all-around motocross at 9 to 11 psi. The Standard grade is published for riders over 90 kg on rocky, hard-packed and high-speed desert terrain at 10 to 12 psi. On a motocross and supercross customer base the Medium and Soft grades are normally the volume sellers. Current grade naming and rider-weight boundaries are confirmed by the factory on request.

What tire pressure should I run with an 80/100-21 mousse?

The published effective pressure equivalent for this size is 8 to 12 psi depending on the density grade selected, against the 12 to 18 psi typically used for a tube setup on the same off-road tire. A 90/90-21 front and an 80/100-21 front do not necessarily run the same tire pressure, because the pressure that keeps the narrower tire planted on a prepared track is not the pressure you would run on a 90/90-21 in sand. The mousse grade and the tire pressure are separate settings.

Quelle est la durée de vie d'une mousse avant de type 80/100-21 ?

Motobike Mas publishes 200 to 500 racing miles as the typical service life for the 80/100-21. A front insert generally outlasts a rear insert on the same machine, because the front carries braking and cornering loads while the rear carries drive torque and generates more heat, and heat is what ages closed-cell foam fastest. For a motocross customer the practical limit is often the number of wheel rebuilds rather than the mileage, because the insert is removed and refitted far more often than it is ridden.

Is the 80/100-21 mousse heavier than an inner tube?

Yes. The published unit weight for the 80/100-21 insert is 0.9 to 1.1 kg, against roughly 400 to 600 g for an inner tube of the same size. The extra mass sits at the wheel, but the mousse still removes up to 40% of the rotating mass a tube plus a heavy-duty rim lock would put on the same end of the bike, so the net effect at the front wheel is lighter than the tube setup it replaces.

La mousse doit-elle être lubrifiée pendant l'installation ?

Yes, and the type matters. Never use petroleum-based lubricants on a mousse insert, because petroleum products degrade nitrile rubber. Use water-based mousse lubricant only, on both the insert and the bead seat of the rim. Two points are specific to this size: check the rim width against the tire fitment marking before mounting, and inspect the insert at every rebuild rather than trusting it from the last session, because a bead levered over the rim during a race-day rebuild can pinch it. The full fitting sequence is in the mousse insert installation guide.

Quelle est la quantité minimale de commande et quel est le délai de livraison ?

The minimum for the 80/100-21 is set per order and confirmed by the factory on request, because this is the highest-volume front size on the line and it is made to order rather than held in stock. Standard OEM production typically runs 15 to 30 days depending on quantity and customization, pre-production samples are available for evaluation, and shipping is by sea on FOB Tianjin terms, by air freight or DDP. Because the 80/100-21 and the 90/90-21 share one production line and one set of tooling, both front sizes can travel on a single purchase order.

Les inserts en mousse Motobike Mas sont-ils certifiés ?

Motobike Mas manufactures tires and mousse inserts under ISO 9001:2015 quality management, to DOT and ECE production standards. Every 80/100-21 insert also passes density, compression recovery, heat resistance, dimensional and structural integrity verification before packing, with dimensional consistency the check that matters most on a high-volume front size, where a batch that varies in profile would reach the customer as a setup change rather than a reject. The certification documentation is on the motorcycle tire certifications page and the inspection regime in the quality control walkthrough.

Order the 80/100-21 enduro mousse insert

The 80/100-21 Professional Enduro Mousse is produced on the Motobike Más line in Tianjin and supplied to dealers, distributors, race teams and aftermarket brands worldwide. It is available in Soft, Medium and Standard densities, with a published unit weight of 0.9–1.1 kg and an effective pressure equivalent of 8–12 psi depending on the grade selected.

Ask for the current minimum, the density mix and the lead time on the 80/100-21, or take a set of pre-production samples before placing a bulk order. Dealers and race teams that need more than one front size can combine the 80/100-21 with the 90/90-21 enduro front on one order, since the two are produced on the same line with the same tooling.

Le 80/100-21 product page contient les spécifications complètes et la page de contact de l'usine takes specification requests directly. Dealers building a motocross and supercross range will also want the mousse selection guide to place the front size against the terrain their customers ride, and the Dossiers de certification ISO 9001, DOT et ECE for the dealer file.

Commentaires

  1. […] rim are set up for, not two ends of the same part. The narrower motocross option is covered in the 80/100-21 mousse insert: motocross front wheel fitment guide and on the 80/100-21 product page, and the full size reference including the rear sizes is in […]

  2. […] is also the size most often paired with the front sizes in the same catalogue: a 90/90-21 front or 80/100-21 front. The full size reference is in Mousse Insert Size Guide: Complete Fitment from Mini Dirt Bikes to […]

  3. […] fitment, reduced performance and a safety risk. The full-size front options are covered in the 80/100-21 motocross front wheel fitment guide and the 90/90-21 off-road enduro and motocross front fitment guide, and the complete size reference […]

  4. […] size has its own guide with the detail that applies to it: the 80/100-21 motocross front, the 90/90-21 enduro front, the 90/100-21 rally front, the 70/100-19 youth front, the 90/100-16 […]

Laisser un commentaire

Votre adresse e-mail ne sera pas publiée. Les champs obligatoires sont indiqués avec *