{"id":832,"date":"2026-11-19T02:26:46","date_gmt":"2026-11-19T02:26:46","guid":{"rendered":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/"},"modified":"2026-11-19T08:05:04","modified_gmt":"2026-11-19T08:05:04","slug":"70-100-19-mousse-insert","status":"publish","type":"post","link":"https:\/\/motobikemas.com\/ru\/70-100-19-mousse-insert\/","title":{"rendered":"70\/100-19 Mousse Insert: Youth MX and Pit Bike Front Fitment"},"content":{"rendered":"<p>The <strong>70\/100-19<\/strong> is the narrow, small-rim front wheel that sits at the front of a junior motocross bike, and it is the one wheel on that machine whose failure the rider cannot ride out of. A closed-cell nitrile rubber insert cut to that one tire carries the load the compressed air would otherwise carry, so a rock under the front wheel or a square edge on a landing does not take the steering away, and it removes up to 40% of the rotating mass that a tube plus a heavy-duty rim lock would put on the front of the bike.<\/p>\n<p>Motobike M&aacute;s builds the 70\/100-19 Front Wheel Motorcycle Mousse (SKU MMO-005) in its own Tianjin factory, published in three density grades &mdash; Soft, Medium and Standard &mdash; with an effective pressure equivalent of 8&ndash;12 psi and a published unit weight of approximately 0.9&ndash;1.1 kg. It is the standard front fitment on the 85cc class and on 125cc and 155cc pit bikes, and it pairs with the 90\/100-16 rear on the same machines. This guide covers the specifications, the density selection for junior rider weights, how it differs from a full-size front, the machines it fits, service life and how distributors order it.<\/p>\n<p><strong>Last updated:<\/strong> 19 November 2026. <strong>Data sources:<\/strong> the published Motobike M&aacute;s specifications for MMO-005, the factory&#8217;s published fitment, density, pressure and lifespan tables, and the factory&#8217;s size and certification documentation. Figures shown as &ldquo;&asymp;&rdquo; are calculated from the published tyre size designations rather than measured by the factory.<\/p>\n<h2>What is a 70\/100-19 front mousse insert?<\/h2>\n<p>A 70\/100-19 is a 70 mm section width on a 100% aspect ratio, which works out at a 70 mm sidewall and an overall diameter of roughly 623 mm on a 19 inch rim. It is the narrowest and the smallest of the three full-size-category front sizes the factory publishes, and that narrowness is the whole design brief: a 70 mm front tire puts less rubber on the ground than an 80 mm or 90 mm front, which makes the bike lighter and quicker to turn but also gives it less grip.<\/p>\n<p>The front wheel is where that trade-off matters more than anywhere else on the bike. A rear tire that lets go costs a junior rider time; a front tire that lets go costs them the ability to steer, on a small machine with a young rider on it, which is the single most dangerous failure in the sport. The insert is what removes that failure mode entirely, because there is no air chamber left inside the carcass to lose.<\/p>\n<p>What the insert does not do is change the size of the tire. A 70\/100-19 insert is cut for a 70 mm section width on a 100% aspect ratio on a 19 inch rim, and it will not seat correctly in an 80\/100-21 or a 90\/90-21 tire even though all three run on the same or a similar rim diameter. The fitting method is in the <a href=\"https:\/\/motobikemas.com\/mousse-insert-installation-guide\/\">mousse insert installation guide<\/a>, and the rear that pairs with this front on the 85cc class is covered in the <a href=\"https:\/\/motobikemas.com\/90-100-16-mousse-insert\/\">90\/100-16 youth rear mousse guide<\/a>.<\/p>\n<h2>70\/100-19 technical specifications<\/h2>\n<p>Read off the sidewall, 70\/100-19 means a 70 mm section width, a 100% aspect ratio and a 19 inch rim diameter. The section width is how much rubber the tire puts on the ground; the aspect ratio is how tall the sidewall is as a percentage of that width. At 100% the two numbers are the same, giving a 70 mm sidewall and an overall diameter of roughly 623 mm.<\/p>\n<p>That overall diameter is the number worth checking against the rear of the same bike. The 90\/100-16 junior rear works out at roughly 587 mm, so a junior bike typically runs a front about 36 mm taller in overall diameter than its rear. That is the reverse of the full-size convention, where a 21 inch front and a 19 inch rear come out within about 14 mm of each other, and it is why the gearing on a junior machine is set for a front that is the larger wheel.<\/p>\n<div class=\"mm-table-scroll\">\n<table>\n<caption>Published data for this SKU against values confirmed on request<\/caption>\n<thead>\n<tr>\n<th scope=\"col\">Data point<\/th>\n<th scope=\"col\">Value<\/th>\n<th scope=\"col\">Status<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Size designation<\/td>\n<td>70\/100-19 &mdash; 70 mm section, 100% aspect ratio, 19 in rim<\/td>\n<td>Published<\/td>\n<\/tr>\n<tr>\n<td>SKU<\/td>\n<td>MMO-005<\/td>\n<td>Published<\/td>\n<\/tr>\n<tr>\n<td>Density grades<\/td>\n<td>Soft \/ Medium \/ Standard<\/td>\n<td>Published<\/td>\n<\/tr>\n<tr>\n<td>Unit weight<\/td>\n<td>Approximately 0.9&ndash;1.1 kg<\/td>\n<td>Published<\/td>\n<\/tr>\n<tr>\n<td>Effective pressure equivalent<\/td>\n<td>8&ndash;12 psi depending on the grade<\/td>\n<td>Published<\/td>\n<\/tr>\n<tr>\n<td>Service life<\/td>\n<td>200&ndash;500 racing miles<\/td>\n<td>Published<\/td>\n<\/tr>\n<tr>\n<td>Rotating mass reduction<\/td>\n<td>Up to 40% against a tube plus a heavy-duty rim lock<\/td>\n<td>Published<\/td>\n<\/tr>\n<tr>\n<td>Country of origin<\/td>\n<td>Tianjin, China<\/td>\n<td>Published<\/td>\n<\/tr>\n<tr>\n<td>Batch dimensional tolerance<\/td>\n<td>Per production batch<\/td>\n<td>Confirmed on request<\/td>\n<\/tr>\n<tr>\n<td>Batch internal density tolerance<\/td>\n<td>Per production batch<\/td>\n<td>Confirmed on request<\/td>\n<\/tr>\n<tr>\n<td>Current grade naming and rider-weight bands<\/td>\n<td>Per SKU<\/td>\n<td>Confirmed on request<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<div class=\"mm-table-scroll\">\n<table>\n<caption>Overall diameter comparison for the 70\/100-19 and the sizes it is confused with<\/caption>\n<thead>\n<tr>\n<th scope=\"col\">Size<\/th>\n<th scope=\"col\">Section width<\/th>\n<th scope=\"col\">Aspect ratio<\/th>\n<th scope=\"col\">Sidewall height<\/th>\n<th scope=\"col\">Rim diameter<\/th>\n<th scope=\"col\">Overall diameter<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>70\/100-19 &mdash; this size<\/td>\n<td>70 mm<\/td>\n<td>100%<\/td>\n<td>&asymp; 70 mm<\/td>\n<td>19 in<\/td>\n<td>&asymp; 623 mm<\/td>\n<\/tr>\n<tr>\n<td>90\/100-16 &mdash; typical youth rear<\/td>\n<td>100 mm<\/td>\n<td>100%<\/td>\n<td>&asymp; 100 mm<\/td>\n<td>16 in<\/td>\n<td>&asymp; 587 mm<\/td>\n<\/tr>\n<tr>\n<td>80\/100-21 &mdash; full-size MX front<\/td>\n<td>80 mm<\/td>\n<td>100%<\/td>\n<td>&asymp; 80 mm<\/td>\n<td>21 in<\/td>\n<td>&asymp; 693 mm<\/td>\n<\/tr>\n<tr>\n<td>90\/90-21 &mdash; full-size enduro front<\/td>\n<td>90 mm<\/td>\n<td>90%<\/td>\n<td>&asymp; 81 mm<\/td>\n<td>21 in<\/td>\n<td>&asymp; 695 mm<\/td>\n<\/tr>\n<tr>\n<td>100\/90-19 &mdash; narrow full-size rear<\/td>\n<td>100 mm<\/td>\n<td>90%<\/td>\n<td>&asymp; 90 mm<\/td>\n<td>19 in<\/td>\n<td>&asymp; 663 mm<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>The &ldquo;&asymp;&rdquo; values are calculated from the published size designations &mdash; sidewall height is the section width multiplied by the aspect ratio, and overall diameter is the rim diameter plus twice the sidewall height. They are useful for comparing sizes against each other and are not factory-measured figures; the factory confirms measured dimensions on request. The full diameter table for every published size is on the <a href=\"https:\/\/motobikemas.com\/mousse-insert-size-guide\/\">mousse insert size guide<\/a>.<\/p>\n<h2>The three density grades for a junior front wheel<\/h2>\n<p>This size is published in three named density grades &mdash; Soft, Medium and Standard &mdash; and each grade comes with a published effective pressure equivalent and a published rider-weight band. On a youth bike that combination is unusually useful, because the range of rider weights on this size is narrow enough that a buyer who does not have the bands to hand will fit the wrong grade to a child.<\/p>\n<p>Why the grade matters this much on a front wheel comes down to steering response. The front is the wheel the rider is actually tuning through every corner, and the foam decides whether the tire conforms to the ground or holds its shape over it. Too firm and the tire bridges over bumps rather than settling onto them, the front goes light over the crest and the rider is left guessing at what the bike is doing. Too soft and the insert gives up early, the shape collapses under load and the steering goes vague in exactly the place the rider needs precision.<\/p>\n<div class=\"mm-table-scroll\">\n<table>\n<caption>Published density grades, effective pressure and rider-weight bands for the 70\/100-19 front wheel<\/caption>\n<thead>\n<tr>\n<th scope=\"col\">Density grade<\/th>\n<th scope=\"col\">Effective pressure equivalent<\/th>\n<th scope=\"col\">Published terrain guidance<\/th>\n<th scope=\"col\">Published rider-weight band<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Soft<\/td>\n<td>8&ndash;10 psi<\/td>\n<td>Mud, sand, loam and wet conditions<\/td>\n<td>Under 50 kg<\/td>\n<\/tr>\n<tr>\n<td>Medium<\/td>\n<td>9&ndash;11 psi<\/td>\n<td>Mixed terrain, all-around use<\/td>\n<td>50&ndash;70 kg<\/td>\n<\/tr>\n<tr>\n<td>Standard<\/td>\n<td>10&ndash;12 psi<\/td>\n<td>Rocky, hard-packed, desert and high-speed<\/td>\n<td>Over 70 kg<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>The published bands for this size are materially different from the full-size range, and that is the single most important line in the table. A rider under 50 kg is specified for the Soft grade on the 70\/100-19, where the same named soft grade on the 80\/100-21 or the 90\/90-21 is specified for riders under 70 kg. A dealer who keeps one soft-grade shelf across all three front sizes is fitting a foam roughly 40% too firm for the youngest riders in the shop.<\/p>\n<p>The published terrain guidance follows the rider weight rather than the other way round: Soft for mud, sand, loam and wet conditions, Medium for mixed terrain and all-around use, Standard for rocky, hard-packed, desert and high-speed riding. The grade is chosen for the rider and the terrain, and the tire pressure is then set separately from the bike&#8217;s own guidance &mdash; they are different settings, and moving one does not move the other. Current grade naming and band boundaries are confirmed by the factory on request, and the naming convention used across the whole range is set out in the <a href=\"https:\/\/motobikemas.com\/mousse-insert-size-guide\/\">mousse insert size guide<\/a>.<\/p>\n<h2>70\/100-19 or a full-size front: where this size belongs<\/h2>\n<p>Three front widths cover most of the off-road market, and none of them is a substitute for another. The 70\/100-19 is the narrow, small-rim front size; the 80\/100-21 and the 90\/90-21 are the full-size fronts. A mousse is size-specific and cut for one tire, so the number on the sidewall is the only input that matters.<\/p>\n<div class=\"mm-table-scroll\">\n<table>\n<caption>70\/100-19 compared with the full-size 80\/100-21 and 90\/90-21 front sizes<\/caption>\n<thead>\n<tr>\n<th scope=\"col\">Specification<\/th>\n<th scope=\"col\">70\/100-19<\/th>\n<th scope=\"col\">80\/100-21<\/th>\n<th scope=\"col\">90\/90-21<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Section width<\/td>\n<td>70 mm<\/td>\n<td>80 mm<\/td>\n<td>90 mm<\/td>\n<\/tr>\n<tr>\n<td>Aspect ratio<\/td>\n<td>100%<\/td>\n<td>100%<\/td>\n<td>90%<\/td>\n<\/tr>\n<tr>\n<td>Rim diameter<\/td>\n<td>19 inch<\/td>\n<td>21 inch<\/td>\n<td>21 inch<\/td>\n<\/tr>\n<tr>\n<td>Typical application<\/td>\n<td>Youth motocross, pit bike and lightweight off-road front<\/td>\n<td>Motocross and supercross front<\/td>\n<td>Enduro, trail and off-road front<\/td>\n<\/tr>\n<tr>\n<td>Published soft-grade rider weight, by size<\/td>\n<td>Under 50 kg<\/td>\n<td>Under 70 kg<\/td>\n<td>Under 70 kg<\/td>\n<\/tr>\n<tr>\n<td>Mousse unit weight<\/td>\n<td>Approximately 0.9&ndash;1.1 kg<\/td>\n<td>Approximately 0.9&ndash;1.1 kg<\/td>\n<td>Approximately 1.0&ndash;1.2 kg<\/td>\n<\/tr>\n<tr>\n<td>Steering character<\/td>\n<td>Lightest and quickest to turn, least stable at speed<\/td>\n<td>Lighter steering, faster turn-in<\/td>\n<td>More front-end grip, slightly heavier steering<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>Two lines in that table decide the question.<\/p>\n<p>The first is rider weight, and it is the line most often missed. The published soft grade on the 70\/100-19 is specified for riders under 50 kg, against under 70 kg on both full-size fronts. The same named grade, applied to a different population, is a firmer foam than the one the junior rider needs.<\/p>\n<p>The second is steering character, and it is where the narrow section width earns its place. A 70 mm front is the quickest of the three to turn in, which on a junior bike with a rider under 50 kg on it is exactly the right characteristic, because the bike needs to be rotated quickly in the tight rhythm sections a youth track is built from. What it gives up is grip at the limit, and on hard-packed or fast terrain the 80\/100-21 front is the more stable choice.<\/p>\n<p>There is one further practical difference that is not about the tire at all, and it catches out parents and dealers alike. The 70\/100-19 runs on a 19 inch rim while both full-size fronts run on 21 inch, and the difference is not cosmetic: the 21 inch front has about 70 mm more overall diameter and about 11 mm more sidewall height. A 21 inch front absorbs a square edge that a 19 inch front transmits to the rim and the rider&#8217;s arms. That is the trade the 80\/100-21 and the 90\/90-21 exist to make, and it is the reason the 70\/100-19 is a youth and pit bike size rather than a full-size one.<\/p>\n<h2>Which machines use a 70\/100-19 front tire?<\/h2>\n<div class=\"mm-table-scroll\">\n<table>\n<caption>Youth, pit bike and lightweight machines that use a 70\/100-19 front tire<\/caption>\n<thead>\n<tr>\n<th scope=\"col\">Class<\/th>\n<th scope=\"col\">Models<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Youth motocross<\/td>\n<td>Kawasaki KX85 and KX100, KTM 85 SX and 105 SX, Husqvarna TC 85, Yamaha YZ85, Honda CRF150R on some model years, Suzuki RM85, GasGas MC 85<\/td>\n<\/tr>\n<tr>\n<td>Pit bike and mini motocross<\/td>\n<td>Honda CRF110F aftermarket builds, SSR 125cc and 140cc, YCF 125cc and 155cc, Pitster Pro 125cc and 155cc, Kay&ouml; 125cc, Thumpstar 125cc and 140cc, aftermarket 19 inch front wheel conversions<\/td>\n<\/tr>\n<tr>\n<td>Lightweight off-road and dual-sport<\/td>\n<td>Honda CRF250F on selected model years with a 19 inch front, Yamaha TT-R230 on selected model years, Suzuki DR200SE on selected model years, small-displacement enduro and trail bikes<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>The 85cc class is the core of this size, and the KTM 85 SX and the 105 SX, the Husqvarna TC 85 and the Yamaha YZ85 are the machines that fill a youth dealer&#8217;s shelf. The pit bike group is the second half of the market, and it is a much larger half than the 65cc class because pit bikes are used year-round rather than in a season.<\/p>\n<p>The last group is the one that needs checking rather than assuming. A small number of lightweight off-road and dual-sport machines were built with a 19 inch front rim &mdash; the Honda CRF250F on selected model years, the Yamaha TT-R230 on selected model years and the Suzuki DR200SE on selected model years &mdash; and those are the cases where a 70\/100-19 front is the factory fitment rather than a youth fitment. On those machines the rider weight bands on this size still apply, which is why the published soft-grade band on the 70\/100-19 starts at under 50 kg while a full-size front&#8217;s does not.<\/p>\n<p>For a distributor, the practical advice is the same as for every size: read the size off the tire. The published list above covers the standard fits, and the factory confirms any specific machine on request.<\/p>\n<h2>Mousse insert compared with an inner tube on the front wheel<\/h2>\n<p>The argument for mousse on the front is not theoretical. These are the practical differences a race team, a pit crew or a parent&rsquo;s customer feels.<\/p>\n<div class=\"mm-table-scroll\">\n<table>\n<caption>70\/100-19 front mousse insert compared with a traditional inner tube<\/caption>\n<thead>\n<tr>\n<th scope=\"col\">Factor<\/th>\n<th scope=\"col\">Mousse insert<\/th>\n<th scope=\"col\">Inner tube<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Flat prevention<\/td>\n<td>Complete &mdash; no air chamber to lose<\/td>\n<td>Vulnerable to pinch flats and punctures<\/td>\n<\/tr>\n<tr>\n<td>Steering precision<\/td>\n<td>Consistent from first practice to last moto<\/td>\n<td>Changes with pressure, temperature and altitude<\/td>\n<\/tr>\n<tr>\n<td>Rotating mass<\/td>\n<td>Lower &mdash; no tube and a lighter rim lock<\/td>\n<td>Higher<\/td>\n<\/tr>\n<tr>\n<td>Front-end safety<\/td>\n<td>No sudden loss of steering control<\/td>\n<td>Sudden loss of steering control on a front flat<\/td>\n<\/tr>\n<tr>\n<td>Maintenance<\/td>\n<td>None once installed<\/td>\n<td>Pressure check before every ride<\/td>\n<\/tr>\n<tr>\n<td>Reusability<\/td>\n<td>Transfer to a new tire if still serviceable<\/td>\n<td>Replaced at every tire change<\/td>\n<\/tr>\n<tr>\n<td>Terrain adaptability<\/td>\n<td>Fixed by the density grade chosen<\/td>\n<td>Adjustable through pressure<\/td>\n<\/tr>\n<tr>\n<td>Installation<\/td>\n<td>Moderate &mdash; the same technique as the rear<\/td>\n<td>Easier<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>Two rows in that table are the ones that decide the question on a junior machine.<\/p>\n<p>The first is front-end safety, and it is stated plainly in the published comparison: a front flat with a tube means sudden loss of steering control, and a front flat with a mousse means there is no steering to lose because the tire has not lost its structure. On a bike where the rider weighs 40 kg and the machine weighs a fraction of what the rider is used to, that difference is the whole argument.<\/p>\n<p>The second is steering precision. A tube&#8217;s pressure drifts with temperature and altitude over a race, so the front that behaved in practice is not necessarily the front that behaves in the race. A mousse holds the carcass behaviour steady for the whole life of the tire, which on a junior bike matters as much as it does on a full-size one &mdash; and on a full-size one the rider has the experience to adapt, which is not always true of a nine-year-old on an 85cc.<\/p>\n<p>The general comparison across sizes, including the rear-wheel cases and the cost side of the argument, is in <a href=\"https:\/\/motobikemas.com\/mousse-insert-vs-inner-tube\/\">mousse insert versus inner tube<\/a>, and the alternative closed-cell systems are compared in <a href=\"https:\/\/motobikemas.com\/mousse-insert-vs-tubliss-system\/\">mousse versus the Tubliss system<\/a>.<\/p>\n<h2>Front wheel and rear wheel: what actually differs<\/h2>\n<p>The published specification for this size is unusual in that it sets the front insert against the rear insert directly, and the comparison is worth reading before a buyer decides whether to fit one or both.<\/p>\n<div class=\"mm-table-scroll\">\n<table>\n<caption>Front mousse insert compared with a rear mousse insert, as published for this size<\/caption>\n<thead>\n<tr>\n<th scope=\"col\">Aspect<\/th>\n<th scope=\"col\">Front mousse (70\/100-19)<\/th>\n<th scope=\"col\">Rear mousse<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Primary demand<\/td>\n<td>Steering precision and bump absorption<\/td>\n<td>Traction and torque transmission<\/td>\n<\/tr>\n<tr>\n<td>Weight impact<\/td>\n<td>Critical for steering feel<\/td>\n<td>Critical for acceleration<\/td>\n<\/tr>\n<tr>\n<td>Heat generation<\/td>\n<td>Lower &mdash; less braking and acceleration load<\/td>\n<td>Higher &mdash; driving load<\/td>\n<\/tr>\n<tr>\n<td>Flat consequence<\/td>\n<td>Immediate loss of steering control<\/td>\n<td>Loss of drive, manageable<\/td>\n<\/tr>\n<tr>\n<td>Typical lifespan<\/td>\n<td>Usually longer than rear<\/td>\n<td>Shorter due to higher loads<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>That table explains the asymmetry that makes the front the more expensive decision of the two. The rear insert carries drive torque and the engine&#8217;s power through the tire for the whole of the run, so it generates more heat and wears faster; the front takes braking and cornering loads, generates less heat and usually outlives the rear. The consequence of a failure is also asymmetric in the opposite direction: a rear that goes down costs the rider time and the bike can still be steered away, while a front that goes down costs the rider control.<\/p>\n<p>Which is why the usual upgrade sequence on a junior bike runs front first. A rear flat ends a run; a front flat ends a rider&#8217;s confidence in a way that takes more than one good race day to undo. The pair that goes together on the 85cc class is this front with the <a href=\"https:\/\/motobikemas.com\/90-100-16-mousse-insert\/\">90\/100-16 rear<\/a>, and both run on the same production line with the same tooling.<\/p>\n<p>The one place this comparison is not a straight win is weight. The published unit weight of the 70\/100-19 is approximately 0.9&ndash;1.1 kg, and the published rotating-mass reduction against a tube plus a heavy-duty rim lock is up to 40% on both wheels &mdash; the absolute saving is smaller at the front than the rear, because the front wheel is the lighter one to begin with, but it is at the end of the bike where mass is felt most in a slow turn-in.<\/p>\n<h2>Installing a 70\/100-19 front mousse insert<\/h2>\n<p><strong>Never use petroleum-based lubricants on a mousse insert.<\/strong> Petroleum products degrade nitrile rubber, and a degraded insert is a liability, not a saving. Use water-based mousse lubricant only, on both the insert and the bead seat of the rim.<\/p>\n<p>The general sequence &mdash; bead seat preparation, lubricant application, first bead, second bead, final seating, and the pressure cycle that sets the profile &mdash; is set out in the <a href=\"https:\/\/motobikemas.com\/mousse-insert-installation-guide\/\">mousse insert installation guide<\/a> and applies unchanged to this size.<\/p>\n<p><strong>Check the rim width before the tire goes on.<\/strong> A 19 inch rim carrying a 70 mm section width leaves more rim wall than the tire needs if the tire is mounted close to the edge of the rim, and a forced insert sits off-centre. That shows up as a front end that never quite settles, and it is worth noting that on a narrow front tire it is easier to miss than on a wide one, because the gap left by the sidewall is less obvious to look at.<\/p>\n<p><strong>Inspect the insert at every refit.<\/strong> A junior wheel is rebuilt often &mdash; between race days, and often more than once in a race day. Every rebuild levers a bead back over a rim, and that is the moment an insert is most likely to be pinched at the bead and to take a compression set that cannot be seen from the outside. Look at the insert each time the wheel is stripped rather than trusting it from the last time it was fitted, and treat any insert that has been levered over a bead as needing an inspection before it goes back in.<\/p>\n<h2>How long does a 70\/100-19 front mousse last?<\/h2>\n<p>Motobike M&aacute;s publishes 200&ndash;500 racing miles as the typical service life for this size. On a youth bike or a pit bike the honest unit is sessions rather than miles, because a small rider covers very little ground in a race day and a pit bike spends most of its life on a short track.<\/p>\n<div class=\"mm-table-scroll\">\n<table>\n<caption>Published mousse insert lifespan by use case<\/caption>\n<thead>\n<tr>\n<th scope=\"col\">Use case<\/th>\n<th scope=\"col\">Terrain<\/th>\n<th scope=\"col\">Expected life<\/th>\n<th scope=\"col\">Tires per mousse<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Motocross (pro)<\/td>\n<td>Groomed tracks, hard pack<\/td>\n<td>30&ndash;60 hours<\/td>\n<td>1 to 2 tires<\/td>\n<\/tr>\n<tr>\n<td>Motocross (amateur)<\/td>\n<td>Varied track conditions<\/td>\n<td>50&ndash;80 hours<\/td>\n<td>2 to 3 tires<\/td>\n<\/tr>\n<tr>\n<td>Enduro (pro)<\/td>\n<td>Technical single-track, rocks, roots<\/td>\n<td>40&ndash;70 hours<\/td>\n<td>1 to 2 tires<\/td>\n<\/tr>\n<tr>\n<td>Enduro (intermediate)<\/td>\n<td>Mixed trail<\/td>\n<td>60&ndash;100 hours<\/td>\n<td>2 to 3 tires<\/td>\n<\/tr>\n<tr>\n<td>Hard enduro<\/td>\n<td>Extreme rock, logs, steep climbs<\/td>\n<td>25&ndash;50 hours<\/td>\n<td>1 tire<\/td>\n<\/tr>\n<tr>\n<td>Desert and rally racing<\/td>\n<td>High-speed rough terrain<\/td>\n<td>30&ndash;60 hours<\/td>\n<td>1 to 2 tires<\/td>\n<\/tr>\n<tr>\n<td>Trail riding (casual)<\/td>\n<td>Maintained trails, fire roads<\/td>\n<td>80&ndash;150 hours<\/td>\n<td>3 to 5 tires<\/td>\n<\/tr>\n<tr>\n<td>Rental fleet<\/td>\n<td>Mixed conditions<\/td>\n<td>60&ndash;120 hours<\/td>\n<td>2 to 4 tires<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>A front insert generally outlives a rear insert on the same machine, and the reason is load rather than geometry: the front wheel absorbs braking energy and cornering loads, while the rear carries drive torque and the engine&#8217;s power through the tire for the whole event. A front insert also works against less heat, and heat is what ages closed-cell foam fastest. The published comparison for this size makes the same point, and the <a href=\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/\">full front-versus-rear breakdown<\/a> above sets out why.<\/p>\n<p>The replacement criteria are the same as for the rest of the range: replace when the mousse feels noticeably softer or spongy compared with new, when there are visible tears, chunks missing or deformation, when the steering feel goes vague and front-end confidence drops in the corners, or when it has been overheated. A mousse should be warm, not hot, and persistent overheating is not recoverable. Storage matters as much as riding conditions &mdash; cool, dry, out of direct sunlight, never compressed or folded, and away from ozone sources such as electric motors and welding equipment &mdash; with a published shelf life of 3&ndash;5 years in sealed packaging. The full criteria across the range are on the <a href=\"https:\/\/motobikemas.com\/mousse-insert-size-guide\/\">mousse insert size guide<\/a> and the <a href=\"https:\/\/motobikemas.com\/mousse-insert-lifespan\/\">mousse insert lifespan page<\/a>.<\/p>\n<h2>How the 70\/100-19 is manufactured and tested<\/h2>\n<p>Motobike M&aacute;s produces mousse in its own Tianjin facility in the Nankai District, covering 50,000 m&sup2; of production floor, warehousing and R&amp;D space. The <a href=\"https:\/\/motobikemas.com\/inside-motobike-mas-smart-manufacturing-facility\/\">full factory walkthrough<\/a> shows the production lines, the storage system and the quality systems behind the range.<\/p>\n<p>The 70\/100-19 is cut as a 19 inch, 70 mm front insert and carries the same inspection regime as the rest of the range: density testing, compression recovery testing, heat resistance testing, dimensional inspection and structural integrity verification before packing. Dimensional consistency is the check that matters most on this size, because a narrow 70 mm insert has to hold its profile tightly for the tire&#8217;s contact patch to stay predictable on a bike whose rider is frequently light on the front end. The full inspection regime is described in the <a href=\"https:\/\/motobikemas.com\/motorcycle-tire-quality-control-process-x-ray-inspection\/\">quality control process walkthrough<\/a>.<\/p>\n<h2>Ordering from Motobike M&aacute;s: MOQ, lead time, shipping and samples<\/h2>\n<p>The 70\/100-19 is supplied as a made-to-order factory line rather than from finished-goods stock. The terms that apply across the range &mdash; the minimum set per order and confirmed on request, standard OEM production at 15&ndash;30 days depending on quantity and customization, pre-production samples for evaluation, and shipping by sea on FOB Tianjin terms, by air freight or DDP &mdash; are published together on the <a href=\"https:\/\/motobikemas.com\/mousse-insert-size-guide\/\">mousse insert size guide<\/a>, the <a href=\"https:\/\/motobikemas.com\/wholesale-mousse-inserts-guide\/\">wholesale buying guide<\/a> and the <a href=\"https:\/\/motobikemas.com\/mousse-insert-oem-odm-manufacturing\/\">OEM and ODM manufacturing<\/a> pages.<\/p>\n<p>For a youth retailer or a pit bike distributor, the useful point in this size is the pairing rather than the minimum. The 70\/100-19 front and the <a href=\"https:\/\/motobikemas.com\/90-100-16-mousse-insert\/\">90\/100-16 rear<\/a> are the standard combination on the 85cc class, they run on the same production line with the same tooling, and they can be combined on a single purchase order and shipped together. A customer who buys a junior front usually needs the rear in the same order, and the front is the one that is easier to leave off a first order &mdash; which is exactly why it is the one that ends up being bought separately at full price later.<\/p>\n<p>Private-label production on this size is available with custom branding, packaging and colours, and with custom density formulations including front-specific formulations, which is what a youth programme running under its own brand usually asks for.<\/p>\n<h2>Frequently asked questions about the 70\/100-19 mousse insert<\/h2>\n<h3>What bikes use a 70\/100-19 front tire?<\/h3>\n<p>The 70\/100-19 front tire size is used on youth motocross bikes in the 85cc class, including the Kawasaki KX85 and KX100, KTM 85 SX and 105 SX, Husqvarna TC 85, Yamaha YZ85 and Suzuki RM85, and on 125cc and 155cc pit bikes including the SSR, YCF, Pitster Pro, Kayo and Thumpstar platforms. It also appears on a small number of lightweight off-road and dual-sport machines built with a 19 inch front rim, such as the Honda CRF250F, Yamaha TT-R230 and Suzuki DR200SE on selected model years.<\/p>\n<h3>Is 70\/100-19 a front or rear tire size?<\/h3>\n<p>70\/100-19 is a front wheel tire size. It is the narrow, small-rim front fitment used on the 85cc class and on pit bikes, and it is never a rear size: a junior bike that runs a 70\/100-19 front normally runs a 90\/100-16 rear, which is the reverse of the full-size convention where the front is the larger wheel.<\/p>\n<h3>Which density grade should I choose for the 70\/100-19 front wheel?<\/h3>\n<p>Three grades are published for this size: Soft, Medium and Standard, each with its own effective pressure equivalent and rider-weight band. The Soft grade is published for riders under 50 kg on mud, sand, loam and wet conditions at 8 to 10 psi. The Medium grade is published for riders 50 to 70 kg on mixed terrain and all-around use at 9 to 11 psi. The Standard grade is published for riders over 70 kg on rocky, hard-packed, desert and high-speed riding at 10 to 12 psi. These bands differ from the full-size fronts, where the soft grade starts at under 70 kg, so a grade should not be carried across between sizes.<\/p>\n<h3>What tire pressure should I run with a 70\/100-19 mousse?<\/h3>\n<p>The published effective pressure equivalent for this size is 8 to 12 psi depending on the grade selected, against the 12 to 18 psi typically used for a tube setup on the same off-road tire. The published rider-weight table puts 8 to 10 psi on the Soft grade for riders under 50 kg, 9 to 11 psi on the Medium grade for 50 to 70 kg, and 10 to 12 psi on the Standard grade for riders over 70 kg. The mousse grade and the tire pressure are separate settings, and a 70\/100-19 front and a full-size front on the same bike do not necessarily run the same tire pressure.<\/p>\n<h3>How long does a 70\/100-19 front mousse last?<\/h3>\n<p>Motobike Mas publishes 200 to 500 racing miles as the typical service life for the 70\/100-19. A front insert generally outlives a rear insert on the same machine, because the front carries braking and cornering loads while the rear carries drive torque and generates more heat, and heat is what ages closed-cell foam fastest. On a junior bike or pit bike the more useful unit is the number of sessions rather than the distance.<\/p>\n<h3>Can I run a mousse on the front wheel only?<\/h3>\n<p>You can, and on a junior machine the front is often the right place to start, because a front flat with a tube means sudden loss of steering control rather than just a lost run. The trade is that the rear insert on this size wears faster than the front, because it carries the drive torque and generates more heat. Many riders fit the front first and add the rear after the first race.<\/p>\n<h3>Is front mousse installation different from rear?<\/h3>\n<p>The technique is the same in both cases, including the rule that only water-based mousse lubricant may be used, because petroleum products degrade nitrile rubber. Two points are worth noting on the front specifically. Check the rim width against the tire fitment marking before mounting, because a narrow 70 mm tire leaves a gap that is easy to miss, and an insert forced into too narrow a rim sits off-centre and makes the steering feel vague in every corner. And inspect the insert at every rebuild rather than trusting it from the last session, because a bead levered over a rim during a race-day rebuild is the most common way an insert picks up a compression set.<\/p>\n<h3>Is the 70\/100-19 mousse heavier than an inner tube?<\/h3>\n<p>Yes. The published unit weight for the 70\/100-19 insert is 0.9 to 1.1 kg, against roughly 400 to 600 g for an inner tube of the same size. The extra mass sits at the wheel, but the mousse still removes up to 40% of the rotating mass a tube plus a heavy-duty rim lock would put on the same end of the bike, so the net effect at the front wheel is lighter than the tube setup it replaces.<\/p>\n<h3>What is the minimum order quantity and the lead time?<\/h3>\n<p>The minimum for the 70\/100-19 is set per order and confirmed by the factory on request, because this size is made to order rather than pulled from finished-goods stock. Standard OEM production typically runs 15 to 30 days depending on quantity and customization, pre-production samples are available for evaluation, and shipping is by sea on FOB Tianjin terms, by air freight or DDP. Because the 70\/100-19 and the 90\/100-16 share one production line and one set of tooling, the junior front and rear pair can travel on a single purchase order.<\/p>\n<h3>Do Motobike Mas mousse inserts carry certification?<\/h3>\n<p>Motobike Mas manufactures tires and mousse inserts under ISO 9001:2015 quality management, to DOT and ECE production standards. Every 70\/100-19 insert also passes density, compression recovery, heat resistance, dimensional and structural integrity verification before packing, with dimensional consistency the check that matters most on a narrow front size, where the profile of the tire depends on the profile of the foam inside it. The certification documentation is on the motorcycle tire certifications page and the inspection regime in the quality control walkthrough.<\/p>\n<h2>Order the 70\/100-19 front mousse insert<\/h2>\n<p>The 70\/100-19 Front Wheel Motorcycle Mousse (SKU MMO-005) is produced on the Motobike M&aacute;s line in Tianjin and supplied to dealers, distributors, race teams and aftermarket brands worldwide. It is available in Soft, Medium and Standard densities, with a published unit weight of approximately 0.9&ndash;1.1 kg and an effective pressure equivalent of 8&ndash;12 psi depending on the grade selected.<\/p>\n<p>Ask for the current minimum, the density mix and the lead time on the 70\/100-19, or take a set of pre-production samples before placing a bulk order. Youth retailers can combine the 70\/100-19 front with the <a href=\"https:\/\/motobikemas.com\/90-100-16-mousse-insert\/\">90\/100-16 youth rear<\/a> on one purchase order, since the two are produced on the same line with the same tooling, and private-label production with front-specific density formulations is available on this SKU.<\/p>\n<p>The <a href=\"https:\/\/motobikemas.com\/product\/70-100-19-front-wheel-motorcycle-mousse-for-motocross-dirt-bikes\/\">70\/100-19 product page<\/a> carries the full specification and <a href=\"https:\/\/motobikemas.com\/contact\/\">the factory contact page<\/a> takes specification requests directly. Dealers building a youth range will also want the <a href=\"https:\/\/motobikemas.com\/mousse-insert-size-guide\/\">mousse insert size guide<\/a> to place the junior front against the full-size range, and the <a href=\"https:\/\/motobikemas.com\/motorcycle-tire-certifications-iso-9001-dot-ece\/\">ISO 9001, DOT and ECE certification documentation<\/a> for the paperwork a youth programme needs.<\/p>\n<p><script type=\"application\/ld+json\">\n{\n  \"@context\": \"https:\/\/schema.org\",\n  \"@type\": \"FAQPage\",\n  \"mainEntity\": [\n    {\n      \"@type\": \"Question\",\n      \"name\": \"What bikes use a 70\/100-19 front tire?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"The 70\/100-19 front tire size is used on youth motocross bikes in the 85cc class, including the Kawasaki KX85 and KX100, KTM 85 SX and 105 SX, Husqvarna TC 85, Yamaha YZ85 and Suzuki RM85, and on 125cc and 155cc pit bikes including the SSR, YCF, Pitster Pro, Kayo and Thumpstar platforms. It also appears on a small number of lightweight off-road and dual-sport machines built with a 19 inch front rim, such as the Honda CRF250F, Yamaha TT-R230 and Suzuki DR200SE on selected model years.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"Is 70\/100-19 a front or rear tire size?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"70\/100-19 is a front wheel tire size. It is the narrow, small-rim front fitment used on the 85cc class and on pit bikes, and it is never a rear size: a junior bike that runs a 70\/100-19 front normally runs a 90\/100-16 rear, which is the reverse of the full-size convention where the front is the larger wheel.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"Which density grade should I choose for the 70\/100-19 front wheel?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Three grades are published for this size: Soft, Medium and Standard, each with its own effective pressure equivalent and rider-weight band. The Soft grade is published for riders under 50 kg on mud, sand, loam and wet conditions at 8 to 10 psi. The Medium grade is published for riders 50 to 70 kg on mixed terrain and all-around use at 9 to 11 psi. The Standard grade is published for riders over 70 kg on rocky, hard-packed, desert and high-speed riding at 10 to 12 psi. These bands differ from the full-size fronts, where the soft grade starts at under 70 kg, so a grade should not be carried across between sizes.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"What tire pressure should I run with a 70\/100-19 mousse?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"The published effective pressure equivalent for this size is 8 to 12 psi depending on the grade selected, against the 12 to 18 psi typically used for a tube setup on the same off-road tire. The published rider-weight table puts 8 to 10 psi on the Soft grade for riders under 50 kg, 9 to 11 psi on the Medium grade for 50 to 70 kg, and 10 to 12 psi on the Standard grade for riders over 70 kg. The mousse grade and the tire pressure are separate settings, and a 70\/100-19 front and a full-size front on the same bike do not necessarily run the same tire pressure.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"How long does a 70\/100-19 front mousse last?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Motobike Mas publishes 200 to 500 racing miles as the typical service life for the 70\/100-19. A front insert generally outlives a rear insert on the same machine, because the front carries braking and cornering loads while the rear carries drive torque and generates more heat, and heat is what ages closed-cell foam fastest. On a junior bike or pit bike the more useful unit is the number of sessions rather than the distance.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"Can I run a mousse on the front wheel only?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"You can, and on a junior machine the front is often the right place to start, because a front flat with a tube means sudden loss of steering control rather than just a lost run. The trade is that the rear insert on this size wears faster than the front, because it carries the drive torque and generates more heat. Many riders fit the front first and add the rear after the first race.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"Is front mousse installation different from rear?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"The technique is the same in both cases, including the rule that only water-based mousse lubricant may be used, because petroleum products degrade nitrile rubber. Two points are worth noting on the front specifically. Check the rim width against the tire fitment marking before mounting, because a narrow 70 mm tire leaves a gap that is easy to miss, and an insert forced into too narrow a rim sits off-centre and makes the steering feel vague in every corner. And inspect the insert at every rebuild rather than trusting it from the last session, because a bead levered over a rim during a race-day rebuild is the most common way an insert picks up a compression set.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"Is the 70\/100-19 mousse heavier than an inner tube?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Yes. The published unit weight for the 70\/100-19 insert is 0.9 to 1.1 kg, against roughly 400 to 600 g for an inner tube of the same size. The extra mass sits at the wheel, but the mousse still removes up to 40% of the rotating mass a tube plus a heavy-duty rim lock would put on the same end of the bike, so the net effect at the front wheel is lighter than the tube setup it replaces.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"What is the minimum order quantity and the lead time?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"The minimum for the 70\/100-19 is set per order and confirmed by the factory on request, because this size is made to order rather than pulled from finished-goods stock. Standard OEM production typically runs 15 to 30 days depending on quantity and customization, pre-production samples are available for evaluation, and shipping is by sea on FOB Tianjin terms, by air freight or DDP. Because the 70\/100-19 and the 90\/100-16 share one production line and one set of tooling, the junior front and rear pair can travel on a single purchase order.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"Do Motobike Mas mousse inserts carry certification?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Motobike Mas manufactures tires and mousse inserts under ISO 9001:2015 quality management, to DOT and ECE production standards. Every 70\/100-19 insert also passes density, compression recovery, heat resistance, dimensional and structural integrity verification before packing, with dimensional consistency the check that matters most on a narrow front size, where the profile of the tire depends on the profile of the foam inside it. The certification documentation is on the motorcycle tire certifications page and the inspection regime in the quality control walkthrough.\"\n      }\n    }\n  ]\n}\n<\/script><\/p>\n<style id=\"mm-table-style-832\">\n.mm-table-scroll{overflow-x:auto;-webkit-overflow-scrolling:touch;margin:26px 0;border:1px solid #e2e8f0;border-top:3px solid #fcd444;border-radius:12px;background:#fff}\n.mm-table-scroll table{width:100%;min-width:620px;border-collapse:collapse;margin:0;font-size:15px;line-height:1.6}\n.mm-table-scroll caption{position:sticky;left:0;caption-side:top;padding:12px 18px;font-size:13px;font-weight:700;letter-spacing:.02em;text-align:left;color:#0f172a;background:#fff}\n.mm-table-scroll thead th{background:#172033;color:#fff;font-weight:600;text-align:left;padding:14px 18px;white-space:nowrap;border:0}\n.mm-table-scroll tbody td{padding:14px 18px;border-top:1px solid #eef2f6;vertical-align:top}\n.mm-table-scroll tbody tr:nth-child(even){background:#f8fafc}\n.mm-table-scroll tbody tr:hover{background:#f1f5f9}\n.mm-table-scroll tbody td:first-child{font-weight:600;color:#0f172a}\n@media (max-width:767px){.mm-table-scroll{border-radius:10px}.mm-table-scroll table{min-width:620px;font-size:14px}.mm-table-scroll caption{padding:10px 14px;width:calc(100vw - 62px);max-width:calc(100vw - 62px);white-space:normal}.mm-table-scroll thead th,.mm-table-scroll tbody td{padding:12px 14px}}\n<\/style>\n","protected":false},"excerpt":{"rendered":"<p>70\/100-19 mousse insert for 85cc youth motocross, pit bike and 19 inch front wheels. Density grades, rider weight bands, bike fitment, MOQ, lead time.<\/p>","protected":false},"author":1,"featured_media":831,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_breakdance_hide_in_design_set":false,"_breakdance_tags":"","footnotes":""},"categories":[187],"tags":[317,332,295,323,330,296,303,302,265,299,305,333,331],"class_list":["post-832","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-mousse-guides","tag-19-inch-mousse","tag-70-100-19-mousse","tag-enduro-mousse","tag-front-wheel-mousse","tag-mini-dirt-bike","tag-motorcycle-mousse","tag-mousse-density","tag-mousse-hardness","tag-mousse-insert-oem","tag-mousse-inserts","tag-off-road-mousse","tag-pit-bike-tire","tag-youth-motocross"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v25.1 (Yoast SEO v25.1) - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>70\/100-19 Mousse Insert | Youth MX Front Fitment Guide<\/title>\n<meta name=\"description\" content=\"70\/100-19 mousse insert for 85cc youth motocross, pit bike and 19 inch front wheels. Density grades, rider weight bands, bike fitment, MOQ, lead time.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/motobikemas.com\/ru\/70-100-19-mousse-insert\/\" \/>\n<meta property=\"og:locale\" content=\"ru_RU\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"70\/100-19 Mousse Insert: Youth MX and Pit Bike Front Fitment\" \/>\n<meta property=\"og:description\" content=\"70\/100-19 mousse insert for 85cc youth motocross, pit bike and 19 inch front wheels. Density grades, rider weight bands, bike fitment, MOQ, lead time.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/motobikemas.com\/ru\/70-100-19-mousse-insert\/\" \/>\n<meta property=\"og:site_name\" content=\"Motobike M\u00e1s\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/motobikemas\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-19T02:26:46+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-19T08:05:04+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"1200\" \/>\n\t<meta property=\"og:image:height\" content=\"630\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Leo\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"\u041d\u0430\u043f\u0438\u0441\u0430\u043d\u043e \u0430\u0432\u0442\u043e\u0440\u043e\u043c\" \/>\n\t<meta name=\"twitter:data1\" content=\"Leo\" \/>\n\t<meta name=\"twitter:label2\" content=\"\u041f\u0440\u0438\u043c\u0435\u0440\u043d\u043e\u0435 \u0432\u0440\u0435\u043c\u044f \u0434\u043b\u044f \u0447\u0442\u0435\u043d\u0438\u044f\" \/>\n\t<meta name=\"twitter:data2\" content=\"25 \u043c\u0438\u043d\u0443\u0442\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#article\",\"isPartOf\":{\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/\"},\"author\":{\"name\":\"Leo\",\"@id\":\"https:\/\/motobikemas.com\/#\/schema\/person\/b2dc0ad07f92acec21c69f163187fd95\"},\"headline\":\"70\/100-19 Mousse Insert: Youth MX and Pit Bike Front Fitment\",\"datePublished\":\"2026-11-19T02:26:46+00:00\",\"dateModified\":\"2026-11-19T08:05:04+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/\"},\"wordCount\":4968,\"commentCount\":2,\"publisher\":{\"@id\":\"https:\/\/motobikemas.com\/#organization\"},\"image\":{\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg\",\"keywords\":[\"19 inch mousse\",\"70\/100-19 mousse\",\"enduro mousse\",\"front wheel mousse\",\"mini dirt bike\",\"motorcycle mousse\",\"mousse density\",\"mousse hardness\",\"mousse insert OEM\",\"mousse inserts\",\"off road mousse\",\"pit bike tire\",\"youth motocross\"],\"articleSection\":[\"Mousse Guides\"],\"inLanguage\":\"ru-RU\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#respond\"]}],\"description\":\"Compare the best enduro mousse options for hardness, heat resistance, rally racing, and extreme enduro. Technical guide for purchasing managers with density specifications and temperature data.\",\"speakable\":{\"@type\":\"SpeakableSpecification\",\"cssSelector\":[\".entry-content h2\",\".entry-content h3\",\".entry-content p\",\".entry-content table\"]}},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/\",\"url\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/\",\"name\":\"70\/100-19 Mousse Insert | Youth MX Front Fitment Guide\",\"isPartOf\":{\"@id\":\"https:\/\/motobikemas.com\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#primaryimage\"},\"image\":{\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg\",\"datePublished\":\"2026-11-19T02:26:46+00:00\",\"dateModified\":\"2026-11-19T08:05:04+00:00\",\"description\":\"70\/100-19 mousse insert for 85cc youth motocross, pit bike and 19 inch front wheels. Density grades, rider weight bands, bike fitment, MOQ, lead time.\",\"breadcrumb\":{\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#breadcrumb\"},\"inLanguage\":\"ru-RU\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"ru-RU\",\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#primaryimage\",\"url\":\"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg\",\"contentUrl\":\"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg\",\"width\":1200,\"height\":630,\"caption\":\"Motobike Mas 70\/100-19 front wheel mousse insert for youth motocross, pit bike and 19 inch front wheels\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/motobikemas.com\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"70\/100-19 Mousse Insert: Youth MX and Pit Bike Front Fitment\",\"item\":\"https:\/\/motobikemas.com\/ru\/ru\/wp-json\/wp\/v2\/posts\/832\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/motobikemas.com\/#website\",\"url\":\"https:\/\/motobikemas.com\/\",\"name\":\"Motobike M\u00e1s\",\"description\":\"Premium Mousse Tires &amp; Motorcycle Tires Manufacturer\",\"publisher\":{\"@id\":\"https:\/\/motobikemas.com\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/motobikemas.com\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"ru-RU\"},{\"@type\":\"Organization\",\"@id\":\"https:\/\/motobikemas.com\/#organization\",\"name\":\"Motobike M\u00e1s\",\"url\":\"https:\/\/motobikemas.com\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"ru-RU\",\"@id\":\"https:\/\/motobikemas.com\/#\/schema\/logo\/image\/\",\"url\":\"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/05\/logo-2.png\",\"contentUrl\":\"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/05\/logo-2.png\",\"width\":1773,\"height\":1086,\"caption\":\"Motobike M\u00e1s\"},\"image\":{\"@id\":\"https:\/\/motobikemas.com\/#\/schema\/logo\/image\/\"},\"sameAs\":[\"https:\/\/www.facebook.com\/motobikemas\",\"https:\/\/www.linkedin.com\/company\/motobikem%c3%a1s\/\"],\"contactPoint\":{\"@type\":\"ContactPoint\",\"telephone\":\"+86-22-1234-5678\",\"contactType\":\"sales\",\"availableLanguage\":[\"English\",\"Chinese\"]},\"address\":{\"@type\":\"PostalAddress\",\"streetAddress\":\"Room 303, Building 2, No. 11 Xihu Road, Nankai District\",\"addressLocality\":\"Tianjin\",\"addressCountry\":\"CN\"},\"description\":\"Premium Mousse Tires & Motorcycle Tires Manufacturer servicing wholesale, OEM, and ODM clients globally.\"},{\"@type\":\"Person\",\"@id\":\"https:\/\/motobikemas.com\/#\/schema\/person\/b2dc0ad07f92acec21c69f163187fd95\",\"name\":\"Leo\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"ru-RU\",\"@id\":\"https:\/\/motobikemas.com\/#\/schema\/person\/image\/\",\"url\":\"https:\/\/secure.gravatar.com\/avatar\/47ba7ecfac9c8459fafecb213e38fb0063318853edd4d92f5c6d3cc6891ad2fc?s=96&d=mm&r=g\",\"contentUrl\":\"https:\/\/secure.gravatar.com\/avatar\/47ba7ecfac9c8459fafecb213e38fb0063318853edd4d92f5c6d3cc6891ad2fc?s=96&d=mm&r=g\",\"caption\":\"Leo\"},\"description\":\"Leo is a motorcycle tire and mousse specialist with over 8 years of experience in off-road tire technology, foam compounding, and enduro product development at Motobike M\u00e1s.\",\"sameAs\":[],\"url\":\"https:\/\/motobikemas.com\/ru\/author\/leo\/\",\"jobTitle\":\"Product Manager, Motobike M\u00e1s\",\"worksFor\":{\"@id\":\"https:\/\/motobikemas.com\/#organization\"},\"knowsAbout\":[\"Motorcycle mousse inserts\",\"Enduro riding\",\"Off-road tire technology\",\"Motorsports equipment\",\"Rubber compounding\",\"Extreme enduro\"]}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"\u0412\u0441\u0442\u0430\u0432\u043a\u0430 Mousse 70\/100-19 | \u0420\u0443\u043a\u043e\u0432\u043e\u0434\u0441\u0442\u0432\u043e \u043f\u043e \u043f\u043e\u0434\u0431\u043e\u0440\u0443 \u043f\u0435\u0440\u0435\u0434\u043d\u0438\u0445 \u0432\u0441\u0442\u0430\u0432\u043e\u043a \u0434\u043b\u044f \u044e\u043d\u043e\u0448\u0435\u0441\u043a\u0438\u0445 \u043c\u043e\u0442\u043e\u0446\u0438\u043a\u043b\u043e\u0432 MX","description":"70\/100-19 mousse insert for 85cc youth motocross, pit bike and 19 inch front wheels. Density grades, rider weight bands, bike fitment, MOQ, lead time.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/motobikemas.com\/ru\/70-100-19-mousse-insert\/","og_locale":"ru_RU","og_type":"article","og_title":"70\/100-19 Mousse Insert: Youth MX and Pit Bike Front Fitment","og_description":"70\/100-19 mousse insert for 85cc youth motocross, pit bike and 19 inch front wheels. Density grades, rider weight bands, bike fitment, MOQ, lead time.","og_url":"https:\/\/motobikemas.com\/ru\/70-100-19-mousse-insert\/","og_site_name":"Motobike M\u00e1s","article_publisher":"https:\/\/www.facebook.com\/motobikemas","article_published_time":"2026-11-19T02:26:46+00:00","article_modified_time":"2026-11-19T08:05:04+00:00","og_image":[{"width":1200,"height":630,"url":"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg","type":"image\/jpeg"}],"author":"Leo","twitter_card":"summary_large_image","twitter_misc":{"\u041d\u0430\u043f\u0438\u0441\u0430\u043d\u043e \u0430\u0432\u0442\u043e\u0440\u043e\u043c":"Leo","\u041f\u0440\u0438\u043c\u0435\u0440\u043d\u043e\u0435 \u0432\u0440\u0435\u043c\u044f \u0434\u043b\u044f \u0447\u0442\u0435\u043d\u0438\u044f":"25 \u043c\u0438\u043d\u0443\u0442"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#article","isPartOf":{"@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/"},"author":{"name":"Leo","@id":"https:\/\/motobikemas.com\/#\/schema\/person\/b2dc0ad07f92acec21c69f163187fd95"},"headline":"70\/100-19 Mousse Insert: Youth MX and Pit Bike Front Fitment","datePublished":"2026-11-19T02:26:46+00:00","dateModified":"2026-11-19T08:05:04+00:00","mainEntityOfPage":{"@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/"},"wordCount":4968,"commentCount":2,"publisher":{"@id":"https:\/\/motobikemas.com\/#organization"},"image":{"@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#primaryimage"},"thumbnailUrl":"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg","keywords":["19 inch mousse","70\/100-19 mousse","enduro mousse","front wheel mousse","mini dirt bike","motorcycle mousse","mousse density","mousse hardness","mousse insert OEM","mousse inserts","off road mousse","pit bike tire","youth motocross"],"articleSection":["Mousse Guides"],"inLanguage":"ru-RU","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#respond"]}],"description":"\u0421\u0440\u0430\u0432\u043d\u0438\u0442\u0435 \u043b\u0443\u0447\u0448\u0438\u0435 \u0432\u0430\u0440\u0438\u0430\u043d\u0442\u044b \u043c\u0443\u0441\u0441\u043e\u0432 \u0434\u043b\u044f \u044d\u043d\u0434\u0443\u0440\u043e \u043f\u043e \u0442\u0432\u0435\u0440\u0434\u043e\u0441\u0442\u0438, \u0442\u0435\u0440\u043c\u043e\u0441\u0442\u043e\u0439\u043a\u043e\u0441\u0442\u0438, \u0434\u043b\u044f \u0440\u0430\u043b\u043b\u0438\u0439\u043d\u044b\u0445 \u0433\u043e\u043d\u043e\u043a \u0438 \u044d\u043a\u0441\u0442\u0440\u0435\u043c\u0430\u043b\u044c\u043d\u043e\u0433\u043e \u044d\u043d\u0434\u0443\u0440\u043e. \u0422\u0435\u0445\u043d\u0438\u0447\u0435\u0441\u043a\u043e\u0435 \u0440\u0443\u043a\u043e\u0432\u043e\u0434\u0441\u0442\u0432\u043e \u0434\u043b\u044f \u043c\u0435\u043d\u0435\u0434\u0436\u0435\u0440\u043e\u0432 \u043f\u043e \u0437\u0430\u043a\u0443\u043f\u043a\u0430\u043c \u0441\u043e \u0441\u043f\u0435\u0446\u0438\u0444\u0438\u043a\u0430\u0446\u0438\u044f\u043c\u0438 \u043f\u043b\u043e\u0442\u043d\u043e\u0441\u0442\u0438 \u0438 \u0442\u0435\u043c\u043f\u0435\u0440\u0430\u0442\u0443\u0440\u043d\u044b\u043c\u0438 \u0434\u0430\u043d\u043d\u044b\u043c\u0438.","speakable":{"@type":"SpeakableSpecification","cssSelector":[".entry-content h2",".entry-content h3",".entry-content p",".entry-content table"]}},{"@type":"WebPage","@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/","url":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/","name":"\u0412\u0441\u0442\u0430\u0432\u043a\u0430 Mousse 70\/100-19 | \u0420\u0443\u043a\u043e\u0432\u043e\u0434\u0441\u0442\u0432\u043e \u043f\u043e \u043f\u043e\u0434\u0431\u043e\u0440\u0443 \u043f\u0435\u0440\u0435\u0434\u043d\u0438\u0445 \u0432\u0441\u0442\u0430\u0432\u043e\u043a \u0434\u043b\u044f \u044e\u043d\u043e\u0448\u0435\u0441\u043a\u0438\u0445 \u043c\u043e\u0442\u043e\u0446\u0438\u043a\u043b\u043e\u0432 MX","isPartOf":{"@id":"https:\/\/motobikemas.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#primaryimage"},"image":{"@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#primaryimage"},"thumbnailUrl":"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg","datePublished":"2026-11-19T02:26:46+00:00","dateModified":"2026-11-19T08:05:04+00:00","description":"70\/100-19 mousse insert for 85cc youth motocross, pit bike and 19 inch front wheels. Density grades, rider weight bands, bike fitment, MOQ, lead time.","breadcrumb":{"@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#breadcrumb"},"inLanguage":"ru-RU","potentialAction":[{"@type":"ReadAction","target":["https:\/\/motobikemas.com\/70-100-19-mousse-insert\/"]}]},{"@type":"ImageObject","inLanguage":"ru-RU","@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#primaryimage","url":"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg","contentUrl":"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/11\/70-100-19-mousse-insert.jpg","width":1200,"height":630,"caption":"Motobike Mas 70\/100-19 front wheel mousse insert for youth motocross, pit bike and 19 inch front wheels"},{"@type":"BreadcrumbList","@id":"https:\/\/motobikemas.com\/70-100-19-mousse-insert\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/motobikemas.com\/"},{"@type":"ListItem","position":2,"name":"70\/100-19 Mousse Insert: Youth MX and Pit Bike Front Fitment","item":"https:\/\/motobikemas.com\/ru\/ru\/wp-json\/wp\/v2\/posts\/832"}]},{"@type":"WebSite","@id":"https:\/\/motobikemas.com\/#website","url":"https:\/\/motobikemas.com\/","name":"Motobike M\u00e1s","description":"\u041f\u0440\u043e\u0438\u0437\u0432\u043e\u0434\u0438\u0442\u0435\u043b\u044c \u0448\u0438\u043d \u0438 \u043c\u043e\u0442\u043e\u0446\u0438\u043a\u043b\u0435\u0442\u043d\u044b\u0445 \u0448\u0438\u043d \u043f\u0440\u0435\u043c\u0438\u0443\u043c-\u043a\u043b\u0430\u0441\u0441\u0430","publisher":{"@id":"https:\/\/motobikemas.com\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/motobikemas.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"ru-RU"},{"@type":"Organization","@id":"https:\/\/motobikemas.com\/#organization","name":"Motobike M\u00e1s","url":"https:\/\/motobikemas.com\/","logo":{"@type":"ImageObject","inLanguage":"ru-RU","@id":"https:\/\/motobikemas.com\/#\/schema\/logo\/image\/","url":"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/05\/logo-2.png","contentUrl":"https:\/\/motobikemas.com\/wp-content\/uploads\/2026\/05\/logo-2.png","width":1773,"height":1086,"caption":"Motobike M\u00e1s"},"image":{"@id":"https:\/\/motobikemas.com\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/motobikemas","https:\/\/www.linkedin.com\/company\/motobikem%c3%a1s\/"],"contactPoint":{"@type":"ContactPoint","telephone":"+86-22-1234-5678","contactType":"sales","availableLanguage":["English","Chinese"]},"address":{"@type":"PostalAddress","streetAddress":"Room 303, Building 2, No. 11 Xihu Road, Nankai District","addressLocality":"Tianjin","addressCountry":"CN"},"description":"\u041f\u0440\u043e\u0438\u0437\u0432\u043e\u0434\u0438\u0442\u0435\u043b\u044c \u0448\u0438\u043d \u0438 \u043c\u043e\u0442\u043e\u0446\u0438\u043a\u043b\u0435\u0442\u043d\u044b\u0445 \u0448\u0438\u043d \u043f\u0440\u0435\u043c\u0438\u0443\u043c-\u043a\u043b\u0430\u0441\u0441\u0430, \u043e\u0431\u0441\u043b\u0443\u0436\u0438\u0432\u0430\u044e\u0449\u0438\u0439 \u043e\u043f\u0442\u043e\u0432\u044b\u0445, OEM \u0438 ODM \u043a\u043b\u0438\u0435\u043d\u0442\u043e\u0432 \u043f\u043e \u0432\u0441\u0435\u043c\u0443 \u043c\u0438\u0440\u0443."},{"@type":"Person","@id":"https:\/\/motobikemas.com\/#\/schema\/person\/b2dc0ad07f92acec21c69f163187fd95","name":"\u041b\u0435\u043e","image":{"@type":"ImageObject","inLanguage":"ru-RU","@id":"https:\/\/motobikemas.com\/#\/schema\/person\/image\/","url":"https:\/\/secure.gravatar.com\/avatar\/47ba7ecfac9c8459fafecb213e38fb0063318853edd4d92f5c6d3cc6891ad2fc?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/47ba7ecfac9c8459fafecb213e38fb0063318853edd4d92f5c6d3cc6891ad2fc?s=96&d=mm&r=g","caption":"Leo"},"description":"\u041b\u0435\u043e - \u0441\u043f\u0435\u0446\u0438\u0430\u043b\u0438\u0441\u0442 \u043f\u043e \u043c\u043e\u0442\u043e\u0446\u0438\u043a\u043b\u0435\u0442\u043d\u044b\u043c \u0448\u0438\u043d\u0430\u043c \u0438 \u043c\u0443\u0441\u0441\u0430\u043c \u0441 \u0431\u043e\u043b\u0435\u0435 \u0447\u0435\u043c 8-\u043b\u0435\u0442\u043d\u0438\u043c \u043e\u043f\u044b\u0442\u043e\u043c \u0440\u0430\u0431\u043e\u0442\u044b \u0432 \u043e\u0431\u043b\u0430\u0441\u0442\u0438 \u0442\u0435\u0445\u043d\u043e\u043b\u043e\u0433\u0438\u0439 \u0432\u043d\u0435\u0434\u043e\u0440\u043e\u0436\u043d\u044b\u0445 \u0448\u0438\u043d, \u043f\u0435\u043d\u043e\u043e\u0431\u0440\u0430\u0437\u043e\u0432\u0430\u043d\u0438\u044f \u0438 \u0440\u0430\u0437\u0440\u0430\u0431\u043e\u0442\u043a\u0438 \u043f\u0440\u043e\u0434\u0443\u043a\u0446\u0438\u0438 \u0434\u043b\u044f \u044d\u043d\u0434\u0443\u0440\u043e \u0432 \u043a\u043e\u043c\u043f\u0430\u043d\u0438\u0438 Motobike M\u00e1s.","sameAs":[],"url":"https:\/\/motobikemas.com\/ru\/author\/leo\/","jobTitle":"Product Manager, Motobike M\u00e1s","worksFor":{"@id":"https:\/\/motobikemas.com\/#organization"},"knowsAbout":["Motorcycle mousse inserts","Enduro riding","Off-road tire technology","Motorsports equipment","Rubber compounding","Extreme enduro"]}]}},"_links":{"self":[{"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/posts\/832","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/comments?post=832"}],"version-history":[{"count":4,"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/posts\/832\/revisions"}],"predecessor-version":[{"id":853,"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/posts\/832\/revisions\/853"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/media\/831"}],"wp:attachment":[{"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/media?parent=832"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/categories?post=832"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/motobikemas.com\/ru\/wp-json\/wp\/v2\/tags?post=832"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}